Project Overview
How a natural stone fabricator used silica air sampling to confirm its workers’ respirable silica exposures stayed below Cal/OSHA limits.
The Challenge
Cutting, drilling, and polishing granite may release respirable crystalline silica (RCS), carcinogenic dust fine enough to reach deep into the lungs. Under Cal/OSHA’s Title 8, Section 5204, as emergency amended in December 2023, stone drilling and cutting are defined as high exposure trigger tasks that require respiratory protection.
The rule has exceptions, but they require proof. Exposures must stay below the Cal/OSHA action level, shown by representative air sampling at least every six months. The fabricator also needed multiple written compliance programs, including hazard communication (HazCom) program for the chemicals in its shop, respiratory protection program, RCS exposure program and a revised Injury and Illness Prevention Program. It asked A-Tech to both draft the programs and keep the silica data current.
What We Did
We started with the plans. Our Certified Safety Professional (CSP) confirmed the current Cal/OSHA requirements and wrote site specific programs covering the shop’s various controlled hazards. For RCS, we built a sampling plan around each work area, with area samples near and away from the drilling and diamond saw zones, and a schedule that repeats every six months to keep the exception in place.
On sampling day, two A-Tech industrial hygienists, supervised by our Certified Industrial Hygienist (CIH), sampled through a regular production shift. NIOSH Method 7500 cannot capture 8 hours on one filter, so each worker and area got two samples of about 4 hours, combined to calculate the OSHA standard 8 hour time weighted average (TWA) for chemical exposure.
- 14 personal breathing zone samples on 7 employees, following each worker between the coldroom, drilling area, diamond saw, and lapping areas
- 8 area samples inside and outside the 2 high exposure zones
- 4 field blanks for quality control
- Analysis for quartz, cristobalite, and tridymite at an AIHA accredited laboratory
- A review of controls in use, including wet cutting, wet drilling, and a remotely operated saw behind a barricade
Every sample, one detection
The Result
Every 8 hour TWA came in below the Cal/OSHA action level of 25 µg/m³ and the Permissible Exposure Limit (PEL) of 50 µg/m³. Of the 22 air samples, 21 were non detect for all three forms of crystalline silica. The only detection was quartz on a drilling area operator, with an 8 hour TWA of 13.1 µg/m³, about half the action level. Area samples both areas where high exposure trigger tasks are located were non detect inside and outside the areas.
We recommended keeping wet methods and dust controls maintained, using wet sweeping or HEPA vacuums instead of dry cleanup, and reassessing whenever equipment, processes, or staffing change. The fabricator now has current silica data supporting its exception, multiple written OSHA programs in place, and sampling continuing every six months.
Highest 8 hour TWA vs Cal/OSHA limits (µg/m³)
25
50
Is Your Shop Due for Silica Sampling?
Frequently Asked Questions
Respirable crystalline silica is very fine dust released when workers cut, grind, drill, or polish stone, concrete, brick, and similar materials containing quartz. The three forms tested are quartz, cristobalite, and tridymite. The particles are small enough to reach deep into the lungs.
Under Cal/OSHA’s RCS standard (Title 8, Section 5204), employers who rely on low exposure data to avoid respirator use near high exposure trigger tasks must sample at least once every six months. Sampling should also be repeated when equipment, processes, materials, or staff change.
Both are 8 hour time weighted averages. The permissible exposure limit (PEL) of 50 µg/m³ is the most a worker may be exposed to. The action level of 25 µg/m³ is half that, and exposures at or above it trigger more requirements, such as periodic monitoring.
Yes, and the risk is higher. Cal/OSHA reports engineered stone can contain more than 93% crystalline silica, compared with about 10 to 45% for granite. More than 90 California countertop workers developed silicosis between 2010 and October 2023.
Yes. Cal/OSHA’s silica standard requires employers to cover respirable crystalline silica in their RCS Exposure Prevention program under Title 8, Section 5204.
Professionals on the job

Patrick Naffah, CIH
Director of Environmental Health & Safety

Ralph Sbargia, CSP
EHS Project Manager


